Differences

This shows you the differences between two versions of the page.

--- pinetime_introduction [2022/02/23 11:43] – [Development] nicolas
+++ pinetime_introduction [2022/03/01 13:09] (current) – [Development] nicolas
@@ Line 1: / Line 1: @@
-====PineTime - 21/02/22 - 19:35====
+====PineTime - 01/03/22 - 13:00====
 https://wiki.pine64.org/wiki/PineTime
@@ Line 46: / Line 46: @@
 cd ~/Documents/PineTime/InfiniTime/build
-cmake -DARM_NONE_EABI_TOOLCHAIN_PATH=/opt/gcc-arm-none-eabi-9-2020-q2-update/ -DNRF5_SDK_PATH=/opt/nRFSDK -DUSE_OPENOCD=1  ../
+cmake -DARM_NONE_EABI_TOOLCHAIN_PATH=/opt/gcc-arm-none-eabi-9-2020-q2-update/ -DNRF5_SDK_PATH=/opt/nRFSDK -DUSE_OPENOCD=1  ../ sudo apt-get install ninja-build
+ sudo apt-get install ninja-build
 </code>
@@ Line 87: / Line 89: @@
 https://lupyuen.github.io/pinetime-rust-mynewt/articles/cloud#add-github-actions-to-our-fork
-I used the develop work flow main.yml on my fork, all runs well.
+I used the develop work flow main.yml on my fork, all runs well. For the time being I will build locally with VSCode.
 nRF Connect For Mobile app to upload the DFU file or use GadgetBridge.
@@ Line 100: / Line 102: @@
 **Cmake tools extension configuration**
+ run chmod u+x YourScriptFileName.sh
 Cmake: Configure Environment
 Environment variables to pass to CMake during configure.
@@ Line 138: / Line 140: @@
 Using the keyboard the following events can be triggered:
-r ... enable ringing
+  *r ... enable ringing
-R ... disable ringing
+  *R ... disable ringing
-m ... let motor run for 100 ms
+  *m ... let motor run for 100 ms
-M ... let motor run for 255 ms
+  *M ... let motor run for 255 ms
-n ... send notification
+  *n ... send notification
-N ... clear all notifications
+  *N ... clear all notifications
-b ... connect Bluetooth
+  *b ... connect Bluetooth
-B ... disconnect Bluetooth
+  *B ... disconnect Bluetooth
-v ... increase battery voltage and percentage
+  *v ... increase battery voltage and percentage
-V ... decrease battery voltage and percentage
+  *V ... decrease battery voltage and percentage
-c ... charging,
+  *c ... charging,
-C ... not charging
+  *C ... not charging
-l ... increase brightness level
+  *l ... increase brightness level
-L ... lower brightness level
+  *L ... lower brightness level
-p ... enable print lvgl memory usage to terminal
+  *p ... enable print lvgl memory usage to terminal
-P ... disable print memory usage
+  *P ... disable print memory usage
-s ... increase step count by 500 steps
+  *s ... increase step count by 500 steps
-S ... decrease step count by 500 steps
+  *S ... decrease step count by 500 steps
-h ... set heartrate running, and on further presses increase by 10 bpm
+  *h ... set heartrate running, and on further presses increase by 10 bpm
-H ... stop heartrate
+  *H ... stop heartrate
+====Run Simulator from VSCode====
-F7 compiles the project
+Install Ninja
-F5 launches the simulator
+<code>
+sudo apt-get install ninja-build
+</code>
+Revise VSCode build script - Notes to be added.
+F7 compiles the project F5 launches the simulator
 -----
@@ Line 169: / Line 178: @@
   *Debugging?
-  *Shake to refresh app view
   *Multiple BLE connections? Handling of BLE messages
   *Make hard wired powered dev board?
-**Notes**
-https://zbm2.com/dokuwiki/doku.php?id=pinetime_introduction
+==== Development Notes====
-==== Development====
 InfiniTime uses LVGL Dev 7.11
@@ Line 190: / Line 194: @@
 https://docs.lvgl.io/7.11/widgets/label.html
+cd ~/Documents/PineTimeSim/InfiniSim/InfiniTime